Shipyard International

WPE SERIES DOUBLE SERVO PUMP CNC BENDING MACHINE

Product features: High speed, high efficiency, fast response, and performance improvement of 30%. The oil supply mode according to demand can reduce overflow and save energy by about 60%. Ultra-high accuracy, positioning accuracy up to 0.005mm. Ultra-low heat energy loss, continuous working temperature rise shall not exceed 15 ℃. At rest, it consumes little power and is quiet. The control system is directly connected with the oil cylinder, eliminating the intermediate pipeline and reducing the chance of oil leakage. CNC system is used to control the mechanical deflection compensation device. The rear stopper is equipped with high-performance servo motor and ball screw. Standard configuration of CyberTouch12 system, optional configuration of CyberTouch 8 CyberTouch_ 15 VT19MX, DA53T, DA58T DA66T S640 and other CNC systems.

A SERIES TORSIONAL SHAFT SYNCHRONOUS BENDING MACHINE

The frame structure adopts all-steel welded structure, and the internal force is eliminated by surface sanding and rust removal treatment and vibration aging treatment, which has good rigidity and stability. The large precision boring and milling machine is used for precision machining by one-time finishing method to ensure the accuracy and quality of the machine tool. The upper and lower motion balance of the cutter beam adopts the forced synchronous operation of the mechanical torsion shaft; The positioning method of mechanical positioning block is adopted to ensure the repeated positioning accuracy of upper mold. Integrated hydraulic system, wide speed adjustment range, stable and reliable operation. Two-stage speed control, first rapid descent (fast forward) and then slow pressurization (work advance). Rear retaining motor drive, manual fine adjustment, digital display. Different bending angles can be obtained by adjusting the bottom dead center position of the press stroke with the hand wheel, which is easy to operate and high in accuracy. The slider three-cylinder automatic compensation and the worktable single-point micro-adjustment structure ensure that the bending angle of the bending parts is uniform throughout the whole length. The working mode includes inching, single and continuous operation. The reversing and pressure holding time can be controlled by time relay. The bending pressure can be adjusted according to the thickness and bending length of the plate.

AB SERIES TORSIONAL SHAFT SYNCHRONOUS BENDING MACHINE (LARGE THROAT)

This model increases the opening height and throat depth on the basis of A series, and is more suitable for the stainless steel door processing industry

AC SERIES TORSIONAL SHAFT SYNCHRONOUS BENDING MACHINE

The opening height and throat depth of the model are increased on the basis of the A series. The frame parameters are the same as those of the AB series. A quick clip is added to facilitate the replacement of the press knife; It is also possible to directly install the upper press knife without installing the quick clip, which is the same as the AB series to achieve larger opening and wider processing range.

AK/ABK/ACK SERIES TORSIONAL SHAFT SYNCHRONOUS CNC BENDING MACHINE

Product features: The model is equipped with GSI single-axis, two-axis and three-axis GSI-P10T CNC system on the basis of A, AB and AC series. The parameters of the frame are the same as the original series. Each axis is controlled by Hofu with high precision. The rear stopper adopts linear guide rail and ball screw, which runs smoothly and has high positioning accuracy.

Sheng Jigang Meets with Shan Zhongde, President of Nanjing University of Aeronautics and Astronautics

On January 31, Sheng Jigang, a member of the Party Leadership Group and deputy general manager of China Shipbuilding Group Co., Ltd., met with a visiting delegation led by Shan Zhongde, president of Nanjing University of Aeronautics and Astronautics at the group headquarters. Focusing on the national strategy of common service, the two sides conducted in-depth exchanges and reached broad consensus on further strengthening strategic cooperation between schools and enterprises, deepening collaborative innovation, and achieving high-quality development.

Make a panel in 40 seconds, which is the central plane of China Shipbuilding International Intelligent Bending

The commissioning of the first set of intelligent sheet metal flexible bending center developed by the Science and Technology Application Design Institute of Guangzhou Shipbuilding International Technology Center (Marine Science and Technology Research Institute) under the China Shipbuilding Group and Guangzhou Shipbuilding International Elevator Electromechanical Equipment Co., Ltd.

China Shipbuilding Group held a briefing on the spirit of the 20th CPC National Congress and the situation and task education

On January 30, China Shipbuilding Group Co., Ltd. held a lecture on the spirit of the 20th CPC National Congress and the situation and task education to mobilize the whole group to fully and accurately understand the spirit of the 20th CPC National Congress, deeply understand the major changes that have not occurred in the current century in the world, better grasp the current international and domestic situation, further unite and lead the cadres and staff to work hard and forge ahead, and accelerate the construction of the world-class shipbuilding group.

The group company and the company have been notified of the cases since 2015

The Discipline Inspection and Supervision Department reported the cases and typical cases occurred in the group company and the company since 2015, and organized to watch the anti-corruption education film "Deadly Break - Warning Record of Huang Baiqing, the former director of the Guangdong Provincial Department of Water Resources and the secretary of the Party Leadership Group's Violation Case", which deeply analyzed the "two sides" life of individual leading cadres who pursued the trade of money and power and used power to make money. Through this study and education, the management personnel participating in the new promotion and key post adjustment said in their learning experience that they were deeply educated, must be exemplary in observing discipline and rules, be honest, do things cleanly, innovate in new posts, and live up to the trust and expectations of the organization.

Analysis of the driving factors for the growth of China's elevator industry

The growth of commercial real estate in China is mainly driven by the development of commercial housing market, office building and commercial business housing market. In terms of the commercial housing market, with the real estate regulation and control started in the second half of 2010, the growth rate of the market slowed down, but the overall idea of macro regulation and control is to curb the speculative demand for commercial housing in the first and second tier cities, while the housing improvement demand and the development of the commercial housing market in the third and fourth tier cities are not within the scope of regulation and control.

Intelligent manufacturing and upgrading of elevator industry to help build smart cities

At the 2022 China International Intelligent Industry Expo, the Market Supervision Administration and Guangzhou Shipbuilding International Elevator Electromechanical Equipment Co., Ltd. built a joint exhibition stand, OTIS CONNECT Internet of Things solution, e-Fusion Sunrise series of home elevators and many other new technologies and smart products were unveiled, helping Guangzhou Shipbuilding International Elevator Electromechanical Equipment Co., Ltd. build a "smart town" and "smart city".